JIC 37° Swivel Female x JIC 37° Male 90° Compact Elbow

A JIC-to-JIC 90° that adds a hard bend to an existing assembly without re-making the hose. The swivel female takes the hose end, the male goes into the port, and nothing gets wound up lining it up.

Brand: Ayrtec – mild steel body with a plated finish, manufactured to the standards listed below.

Watch: How to Assemble Hydraulic Hose Fittings: Identification and Guide on JIC Thread Types

Thread Standards

• JIC 37° Swivel Female – SAE J514 37° flare. It seals on the 37° cone seat and swivels, so the hose is never wound up during assembly.
• JIC 37° Male – SAE J514 37° flare. It seals metal-to-metal on the 37° cone, so it takes no tape at all.

How to Choose

• Both ends are 37° cone. Sizes do not have to match, and a female 12 to male 08 is a common way to step down at the port.
• JIC 37° and SAE 45° flare look similar and share thread sizes. The wrong cone angle seals briefly then weeps.
• Never tape a JIC thread. It seals on the cone and tape only holds the cone off its seat.

Technicians Advice

Bring the swivel nut up until the cones meet, then a defined amount further - about a sixth of a turn on small sizes, a quarter on large. Chasing a JIC weep with more torque flattens the cone and turns a reusable joint into scrap.

Where You’ll Find It

• JIC 37° Swivel Female – Hose ends on imported machinery, where the swivel lets the assembly be fitted without winding up the hose.
• JIC 37° Male – Hose ends and ports on imported US and Asian machinery – Caterpillar, John Deere, Case IH, New Holland, Bobcat, Kubota, Takeuchi.

Cross-Reference

• JIC 37° Swivel Female – SAE J514 / ISO 8434-2 37° flare. Parker series Triple-Lok.
• JIC 37° Male – SAE J514 / ISO 8434-2 37° flare. Parker call this series Triple-Lok. The industrial cousin of the AN 37° flare used in aviation and motorsport.

Parker, Gates, Aeroquip and Ryco all manufacture to these same standards under their own part numbering, so a fitting built to the standard above will mate with theirs.

Cross-references are given at series level as a guide to the standard, not as a part-for-part substitution. Always confirm the thread form, size and seal type against the port before ordering.

📐Dimensions & thread sizes – every size in this range

← Swipe the table sideways to see every measurement →

Part code	A	B	H	S1	Material	Finish
JIF-JIM-90C-0707	7/16" JIC	7/16" JIC	14.3mm	11.1mm	Mild steel	Plated finish
JIF-JIM-90C-0808	1/2" JIC	1/2" JIC	15.9mm	14.3mm	Mild steel	Plated finish
JIF-JIM-90C-0909	9/16" JIC	9/16" JIC	17.5mm	14.3mm	Mild steel	Plated finish
JIF-JIM-90C-0912	3/4" JIC	9/16" JIC	17.5mm	19.1mm	Mild steel	Plated finish
JIF-JIM-90C-1212	3/4" JIC	3/4" JIC	22.2mm	19.1mm	Mild steel	Plated finish
JIF-JIM-90C-1214	7/8" JIC	3/4" JIC	22.2mm	22.2mm	Mild steel	Plated finish
JIF-JIM-90C-1217	1.1/16" JIC	3/4" JIC	22.2mm	27.0mm	Mild steel	Plated finish
JIF-JIM-90C-1412	3/4" JIC	7/8" JIC	25.4mm	22.2mm	Mild steel	Plated finish
JIF-JIM-90C-1414	7/8" JIC	7/8" JIC	25.4mm	22.2mm	Mild steel	Plated finish
JIF-JIM-90C-1417	1.1/16" JIC	7/8" JIC	25.4mm	27.0mm	Mild steel	Plated finish
JIF-JIM-90C-1712	3/4" JIC	1.1/16" JIC	31.8mm	27.0mm	Mild steel	Plated finish
JIF-JIM-90C-1714	7/8" JIC	1.1/16" JIC	31.8mm	27.0mm	Mild steel	Plated finish
JIF-JIM-90C-1717	1.1/16" JIC	1.1/16" JIC	31.8mm	27.0mm	Mild steel	Plated finish
JIF-JIM-90C-2117	1.1/16" JIC	1.5/16" JIC	41mm	33mm	Mild steel	Plated finish
JIF-JIM-90C-2121	1.5/16" JIC	1.5/16" JIC	38.1mm	33.3mm	Mild steel	Plated finish
JIF-JIM-90C-2626	1.5/8" JIC	1.5/8" JIC	50.8mm	41.3mm	Mild steel	Plated finish
JIF-JIM-90C-3030	1.7/8" JIC	1.7/8" JIC	57.2mm	47.6mm	Mild steel	Plated finish
JIF-JIM-90C-4040	2.1/2" JIC	2.1/2" JIC	76.2mm	63.5mm	Mild steel	Plated finish

Key: H centre to face, S1 hex across flats 2. Measurements in millimetres unless shown otherwise. Thread columns show what each end mates with. Dimensions are nominal – check critical clearances against the part.

Downloads

📄 Thread Identification Chart (PDF)

Same Threads, Other Angles

🔗 Straight – same threads🔗 45° Compact – same threads🔗 45° Swept – same threads🔗 90° Swept – same threads

Express shipping Australia-wide. We dispatch daily to New South Wales, Victoria, Queensland, Western Australia, South Australia, Tasmania, the Australian Capital Territory and the Northern Territory – Sydney, Melbourne, Brisbane, Perth, Adelaide, Hobart, Canberra and Darwin, plus regional and remote sites.

Need a hand? Call 1300 146 737 or email sales@mhfgc.com.au – real technicians, real answers.