Metric Light (L) Swivel Female x Metric Light (L) Male 90° Compact Elbow

DIN 2353 light-series 24° cone both ends, turned 90°, with a swivel on one side so an existing line can be turned without cutting tube. The everyday European return, drain and pilot line elbow.

Brand: Ayrtec – mild steel body with a plated finish, manufactured to the standards listed below.

Watch: Exploring Hydraulic Adaptors Part 1: Difference Between Branch Tee & Run Tee, Elbows Short and Long

Thread Standards

• Metric Light (L) Swivel Female – DIN 2353 / ISO 8434-1 24° cone, light series. It pulls onto the mating 24° cone and swivels so the tube is not twisted.
• Metric Light (L) Male – DIN 2353 / ISO 8434-1 24° cone, light series. It seals on the 24° cone, normally with an O-ring captured in the cone.

How to Choose

• Light (L) suits moderate pressure. If the original was heavy series, do not step down just because the thread fits.
• Metric sizes are quoted by tube outside diameter - a 12L is for 12mm tube.
• Check whether the cone carries an O-ring or is bare metal and match it to the mating fitting.

Technicians Advice

The swivel nut should turn freely by hand until the cones meet. If it loads up early the cone is not square - back it off and start again. A soft-seal cone run against a hard-seal part will feel tight and still weep, because the O-ring is carrying nothing.

Where You’ll Find It

• Metric Light (L) Swivel Female – European tube and hose assemblies on the lower-pressure side.
• Metric Light (L) Male – European-built machinery – Liebherr, Wacker Neuson, Atlas, Sennebogen, Manitou – and imported tube assemblies. Light series suits return, drain and pilot lines.

Cross-Reference

• Metric Light (L) Swivel Female – DIN 2353 / ISO 8434-1 24° cone, light (L) series. Parker EO / EO-2.
• Metric Light (L) Male – DIN 2353 / ISO 8434-1 24° cone, light (L) series. Parker call this range EO and EO-2, historically branded Ermeto. Also called bite type.

Parker, Gates, Aeroquip and Ryco all manufacture to these same standards under their own part numbering, so a fitting built to the standard above will mate with theirs.

Cross-references are given at series level as a guide to the standard, not as a part-for-part substitution. Always confirm the thread form, size and seal type against the port before ordering.

📐Dimensions & thread sizes – every size in this range

← Swipe the table sideways to see every measurement →

Part code	S	S1	Material	Finish
MLF-MLM-90C-1212	12mm	14mm	Mild steel	Plated finish
MLF-MLM-90C-1414	12mm	17mm	Mild steel	Plated finish
MLF-MLM-90C-1616	14mm	19mm	Mild steel	Plated finish
MLF-MLM-90C-1818	17mm	22mm	Mild steel	Plated finish
MLF-MLM-90C-2222	19mm	27mm	Mild steel	Plated finish
MLF-MLM-90C-2626	24mm	32mm	Mild steel	Plated finish
MLF-MLM-90C-3030	27mm	36mm	Mild steel	Plated finish
MLF-MLM-90C-3636	36mm	41mm	Mild steel	Plated finish
MLF-MLM-90C-4545	41mm	50mm	Mild steel	Plated finish
MLF-MLM-90C-5252	50mm	60mm	Mild steel	Plated finish

Key: S hex across flats, S1 hex across flats 2. Measurements in millimetres unless shown otherwise. Thread columns show what each end mates with. Dimensions are nominal – check critical clearances against the part.

Downloads

📄 Thread Identification Chart (PDF)

Same Threads, Other Angles

🔗 Straight – same threads

Express shipping Australia-wide. We dispatch daily to New South Wales, Victoria, Queensland, Western Australia, South Australia, Tasmania, the Australian Capital Territory and the Northern Territory – Sydney, Melbourne, Brisbane, Perth, Adelaide, Hobart, Canberra and Darwin, plus regional and remote sites.

Need a hand? Call 1300 146 737 or email sales@mhfgc.com.au – real technicians, real answers.